Skip to content
Narrow screen resolution Wide screen resolution Auto adjust screen size Increase font size Decrease font size Default font size

gumstix developer site

Home arrow Documentation arrow Hardware arrow Gumstix Overo COMs: 70-pin connector J1 features the LCD, PWM and analog signals
Gumstix Overo COMs: 70-pin connector J1 features the LCD, PWM and analog signals

Last Update: May 12th and July 20th to add Pin 9 notes,

Prior Update: April 8th to add Note #8 below.

Gumstix Overo COM: Signals document V1.2 (March 25th, 2010)  download here

J1 Connector Notes:

  1. All logic is at 1.8V

  2. The input range of the supply voltage is approximately 3.3V – 4.2V.

  3. The signals of connectors J1 are connected directly to the OMAP3503 without buffers.

  4. USBOTG interface supports high speed USB (480MBs).

  5. Pin 62 and Pin 63 labeled as TV_OUT1 and TV_OUT2, respectively, for future use.

  6. Pin 8 was incorrectly labeled as GPIO127_TS_IRQ. Pin 8 is now correctly labeled as GPIO_10

  7. Pin 14 was incorrectly labeled as GPIO128_GPS_PPS. Pin 14 is now correctly labeled as GPIO_186

  8. The physical location of pin 1 of the J1 connector can be found on the layout PDF for the Overo COM via here.

  9. Some notes re JTAG and J1-9 (GPIO_31) have been linked below.

Comments Signal Pin Pin
Signal Comments

Use to trigger hard reset (i.e. power-on reset).

N_MANUAL_RESET
1
70 GND

GPIO71_L_DD01 2 69 HSORF

GPIO70_L_DD00 3 68 HSOLF

GPIO73_L_DD03 4 67 VSYSTEM board supply: 3.3V - 4.2V

GPIO75_L_DD05 5 66 VSYSTEM board supply: 3.3V - 4.2V

GPIO72_L_DD02 6 65 POWERON Connected to PWRON on PMIC

GPIO74_L_DD04 7 64 ADCIN7

GPIO_10 8 63 TV_OUT1
 (for future u
  • Overo COMs R2173 to R2516: J1 pin 9 is GPIO0_WAKEUP; GPIO31 goes to a test point on the board only.
  • Overo COMs revs  2606 and higher: J1 pin 9 is GPIO31_WAKEUP  GPIO0 is used as the IRQ from the TPS65950.
  • For more information on using JTAG and J1-9 (GPIO_31), go here .
GPIO0_WAKEUP
9 62 TV_OUT2
 (for future use)

GPIO185_I2C3_SDA 10 61 GPIO93_L_DD23

GPIO80_L_DD10 11 60 GPIO82_L_DD12

GPIO81_L_DD11 12 59 SYSEN Connected to SYSEN on PMIC

GPIO184_L_I2C3_SCL 13 58 ADCIN2

GPIO_186 14 57 MIC_MAIN_MF

GPIO92_L_DD22 15 56 GND

GPIO147_GPT8__PWM 16 55 GPIO145_GPT10_PWM

GPIO83_L_DD13 17 54 USBOTG_VBUS power out from the PMIC

GPIO144_GPT9_PWM 18 53 ADCIN6

GPIO84_L_DD14 19 52 VBACKUP Backup battery input to PMIC

GPIO85_L_DD15 20 51 ADCIN5

GPIO146_GPT11_PWM 21 50 AGND


GPIO163_IR_CTS3 22 49 PWM1

GPIO91_L_DD21 23 48 ADCIN3

GPIO87_L_DD17 24 47 GPIO170_HDQ_1WIRE

GPIO88_L_DD18 25 46 USBOTG_ID

GPIO166_IR_TXD3 26 45 GPIO90_L_DD20

GPIO89_L_DD19 27 44 GPIO86_L_DD16

GPIO79_L_DD09 28 43 GPIO69_L_BIAS

GPIO77_L_DD07 29 42 PWM0

GPIO78_L_DD08 30 41 AUXRF

GPIO165_IR_RXD3 31 40 ADCIN4

GPIO66_L_PCLK 32 39 MIC_SUB_MF

GPIO76_L_DD06 33 38 AUXLF

GPIO68_L_FCLK 34 37 USBOTG_DM

GPIO67_L_LCLK 35 36 USBOTG_DP

Tags